Transmission Control Valve - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 3/8 by 16 NC by 5 (Guide Bolt) | 2 | |
B | 138-7573 | Link Bracket | 2 |
C | 5P-2187 | Lifting Bracket | 1 |
D | 5P-2184 | Bracket | 1 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install bolts (17). Tighten bolts (17) to a torque of
30 ± 4 N·m (22 ± 3 lb ft) . Remove Tooling (D). The weight of transmission control valve (18) is approximately55 kg (120 lb) .Note: Use Tooling (D) to balance transmission control valve (18).
- Attach Tooling (C) and Tooling (D) to a suitable lifting device. Install transmission control valve (18). Install bolts (16). Tighten bolts (16) to a torque of
48 ± 4 N·m (35 ± 3 lb ft) . Remove Tooling (C).Show/hide tableIllustration 3 g00927189 - Slide tubes (15) toward the front of the machine.
Show/hide table
Illustration 4 g00927188 - Install plates (14) and install bolts (13).
Show/hide table
Illustration 5 g01068532 - Connect pins (11) to stems (12).
- Slide couplings (10) to the front of the machine. Tighten nuts (9) to the original location.
Show/hide table
Illustration 6 g01068485 - Install flanges (4) and bolts (6).
- Install switch (5).
Show/hide table
Illustration 7 g00927157 - Attach Tooling (B) to cover (3). Attach a suitable lifting device to Tooling (B) and install cover (3). The weight of cover (3) is approximately
23 kg (50 lb) .Show/hide tableIllustration 8 g00927147 - Install Tooling (A) in order to align the bolt holes and support the cover. Connect harness assemblies (1). Install 24 bolts (2).
- Remove Tooling (A) and install the remaining two bolts (2).
- Fill the transmission with fluid. Refer to Operation and Maintenance Manual, "Transmission and Differential Oil - Change".
Show/hide table
Illustration 1 | g00927191 |
Show/hide table
Illustration 2 | g00927193 |
End By:
- Install the rear chassis support. Refer to Disassembly and Assembly, "Rear Chassis Support - Install".
Caterpillar Information System:
AP-655C and BG-2255C Asphalt Pavers Machine Systems Chain (Drag Conveyor) - Remove and Install
AP-655C and BG-2255C Asphalt Pavers Machine Systems Chain (Auger Conveyor) - Remove and Install
216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Reference Material
AS2251 and AS2301 Front Mounted Screed Screed Plate (Main) - Remove and Install - CWF1-UP
16H Motor Grader Power Train Transmission Control Valve - Remove
CB-214E, CB-224E and CB-225E Vibratory Compactors Propel System Electrical Schematic
AS2251 and AS2301 Screeds Hydraulic Cylinder (Extender Extend) - AS-2301
AP-655C and BG-2255C Asphalt Pavers Machine Systems Piston Pump (Auxiliary) - Install
120M and 12M Motor Graders Cooling System Coolant Level - Check
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Hydraulic Pedal Control
16H Motor Grader Power Train Gear Pump (Transmission Charging and Scavenge) - Install
254-0348 Control Gp-Parking Brake (Automatic) Custom Product Support Literature for the R1700G <B>S/N:</B>8XZ1-UP Load Haul Dump{1408, 4250} 254-0348 Control Gp-Parking Brake (Automatic) Custom Product Support Literature for the R1700G <B>S/N:</B>8XZ1-UP Load Haul Dump{1408, 4250}
12M Motor Grader Fuel System - Fill
12M Motor Grader Fuel System - Prime
Installation of Extensions on the Body for the Ejector Blade{6060, 6203, 7250, 7258} Installation of Extensions on the Body for the Ejector Blade{6060, 6203, 7250, 7258}
AS2251 and AS2301 Screeds Extender Carriage
16H Motor Grader Power Train Transmission and Transfer Gears - Remove
AS2251 and AS2301 Front Mounted Screed Glow Plug - Remove and Install - CWF1-UP
AS2251 and AS2301 Front Mounted Screed Burner Blower Motor - Remove and Install - CWF1-UP
AS2251 and AS2301 Front Mounted Screed Burner Group (Main) - Remove - CWF1-UP
Installation Instructions for the Engine Oil Lines Group for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307, 1714} Installation Instructions for the Engine Oil Lines Group for the Hydraulic Electronic Unit Injector (HEUI) Pump{1307, 1714}
AS2251 and AS2301 Front Mounted Screed Burner Group (Extender) - Remove - CWF1-UP
AS2251 and AS2301 Front Mounted Screed Burner Group (Main) - Install - CWF1-UP
AS2251 and AS2301 Front Mounted Screed Burner Group (Extender) - Install - CWF1-UP